Readymade & Prefabricated Office Manufacturer and Supplier

Construction details of M.S. Prefabricated Sales Office (Lift & Shift type): This specification only for new fabricated.

Shell: The shell shall be fabricated from tested quality steel duly welded, comprising of base frame, peripheral structure, self draining roof, entry doors and of windows (as per requirement). The Four Top corners shall be sufficiently strengthened to facilitate transportation, lifting and placing.

Base Frame: The base frame shall be made of pressed mild steel channel section 125 x 70mm C Channel and 100x50mm I-Channel for Cross Sections.

Side and End Walls: The side and end frame shall be made out of pressed sections of suitable profiles/pillars of sufficient strength. Exterior wall shall be made up of 18 swg. MS specially corrugated sheet whereas 8 mm MDF board will be used for interior walls. The steel sheet shall be treated for corrosion resistant. Panels shall be vertically corrugated, sheet shall be continuously welded to top side and base structure so as to offer better strength to weight ratio. All gaps will be sealed at edges and at seams, bottom etc to prevent ingress of moisture.

 20’ = 75x75mm Square Pipe with 3.2mm thickness
 40’ = 75x75mm Square Pipe with 3.2mm thickness

Flooring Systems: On the bottom frame 19 mm thick Marine Plywood shall be fixed by means of self taping screw. PVC vinyl flooring shall be fixed on the panel.

Roof: We as Readymade Office Manufacturer gives a self draining type roof shall be made out of 18 swg. M.S. sheet, adequate roof bows are to be provided. Roof shall be adequately cambered for draining of rain water. Interior paneling shall be done in 9 mm MDF board with adequate insulation.

Paint: Epoxy Zinc Phosphate primer & synthetic Epoxy paint for final 2 coats. (Corrosion free and fire proof paints)

Insulation: 50 mm thick Glass wool insulation shall be used for walls and 50 mm thick Glass wool insulation to be provided for roof.

Inner Paneling: The interior shall be aesthetically finished so as to give custom built appearance with extremely high quality workmanship. All vertically and horizontal corners shall be neatly and smoothly finished with Aluminum sections. The paneling of side walls and roof shall be of 9 mm thick decorative laminated board.

Main Entry Door: The door shall be of external opening type made out of the same material as wall panels with door closing unit. The Prefabricated Sales Office door shall be double skin steel construction with 40 mm thick Glass wool insulation. The peripheral edges of the door shall be sealed with double gaskets to make it waterproof & leak proof. The door interior shall be finished with same material matching with that of the bunk house interior. The door shall be provided with locking arrangement with separate handles of both sides of the door as required. Main door will be insulated and fitted with appropriate lock and power bolt.

Aluminum Windows: Aluminum powder coated windows, sliding type shall be provided, made of aluminum section, 4 mm thick, clear vision glasses are to be fitted to it.

Electrical System: We as a Readymade Office Manufacturer for bunk house will be provided with electrical wiring suitable for 250 volt, 50 HZ single phase AC power supply. All electrical wiring shall be concealed. Suitable copper cables shall be used for lighting circuits. The copper cables used will be of 2.5 mm cable for lighting circuits. ISI mark and concealed in PVC conduits insulated copper wire shall be used foe wiring to be done in PVC conduit with small size distribution board with MCB protection and to separate with main supply.
Prefabricated Office Manufacturer We, Prefabricated Office Manufacturer offer a wide range of prefabricated office with PUF insulated panels; EPS insulated panels and Light gauge steel framing solution. In an era where time is money, prefabricated office is a solution, as it is quick and easy to erect. We,Prefabricated Office Manufacturer offer complete solutions for prefabricated site office under one roof starting from designing to installation.
While designing the prefabricated office building, we, Prefabricated Office Manufacturer consider factors like daylight and ventilation for fresh air. Moreover these prefabricated offices are constructed with insulated panels. Therefore, prefabricated offices are best suited for adverse climatic conditions. Prefabricated offices have walls of different heights, but then too, strong and sturdy. We, Prefabricated Office Manufacturer are providing the best prefabricated office installation services in various places in India. We, Prefabricated Office Manufacturer are able to install a vast variety of prefabricated office all over India. We have rich and wide industrial knowledge in our trained professionals. The prefabricated site office is made of high quality steel frame and is offered in varied specification to suit different needs of our clients. It includes bunk units that suits for storage, on-site accommodation and offices.


Explore our website to find out more about business process, designs and do invite us
Contact Us

Landline :
(022) 64467870 / 64205773

Phone : 09224112660 / 09224147510                     09223080556 / 08976726666

Email :